[PC] QB 02 | BEP 01

The birth of the plumbing profession in the Philippines was traced back to

Based on the history of plumbing practice “The wall city” known as Intramuros was established as a model community by the?

When was the first time of inclusion of “asbestos cement pipe” as an approved material?

The Filipino plumbers were assigned the task of maintaining, repairing/remodeling plumbing system in all pueblos or town, church and government buildings during?

Based on the history of plumbing practice, plumbing took a great leap at the turn of the American soldiers, engineers, Thomasite teachers, doctors and evangelist.

Before Martial Law, Republic Act No. 6541 known as the?

Based on the history of plumbing practice, who was the Governor General issued letter of instruction on proper waste disposal when epidemics like cholera, leprosy and other contagious disease engulfed in the Philippines.

The first chief of the Division of the Plumbing Construction and Inspection.

Who was the NAMPAP President spearheaded the updating of the RNPCP in 1996?

When was the NAMPAP organized and had it registered with the Securities and Exchange Commission.

Known as “Plumbing Law of the Philippines” was signed by President Ramon Magsaysay in june 18, 1955.

When was the National Plumbing Code of the Philippines promulgated and approved by Malacañang?

When was the Board of Examiners for Master Plumber and NAMPAP prepared the Curriculum for Plumbing Engineering and approved by DepED at Feati University?

Plumbing Engineering was first introduced to what School or University?

City Ordinance No.2411 known as the?

Who is the Chairman of Board of Master Plumbers (BOMP) where the NAMPAP submitted the draft code to him in October 1999.

Who is the Chairman of PRC where adopted RNPCP 1999 which Pres. Joseph Estrada approved last Dec. 21, 1999.

RNPC 1999 was approved by Pres. Joseph Estrada last _____.

An adequate _____ is one of the most important governances in modern and healthful human existence.

How many set of plan shall be submitted of the aforementioned requirements with each application for a permit signed and sealed by RMP.

How many set(s) of approved plumbing plan, data and specification will retain by the Administrative Authority.

How many set(s) of approved plumbing plan, specification and data will retain to applican and owner?

How many set(s) of plan shall be kept or retain to a jobsite at all times while the work is in progress.

A plumbing permit issued shall expire and become null and void if the plumbing work authorized therein is not commenced within _____ from the date issued.

An outhouse or structure used for the deposition of excrement.

If the plumbing work is suspended or abandoned at any time after having been commenced for a period of _____.

In case of renewal of a plumbing permit from the sanction due to expired permit what will be the equivalent fee shall be paid?

Where shall be a registration number in a round shaped seal placed?

Where shall be the word “Registered and Licensed Master Plumber” in a round shaped seal placed?

Where shall be the name of Registered and Licensed Master Plumber in a round shaped seal placed?

An organization primarily established for purposes of testing to approved standards.

It includes the Building official, the Commision, the Board who can established and authorize to administrative and enforce the provision of R.A 1378.

The flow of water or other liquids,mixtures or substances into the distributing pipes of a potable water supply from any source other than from its intended source.

Occurs due to an increased reverse pressure above the supply pressure. Ex: pumps, boilers, gravity or other source of pressure.

The flowing back of used, contaminated or polluted water from a plumbing fixture or vessel into a water supply pipe due to negative pressure in such pipe.

Any joint obtained by joining of metal parts which alloys will melts at a temp. higher than 449 degrees centigrade but lower than the melting temp of the parts to be joined.

A group vent pipe which starts in front of the extreme fixture connection on a horizontal branch and connects to the vent stack. (See Loop vent)

A sewer intended to receive sanitary sewage with or without industrial waste and without the admisxture of rain or ground water.

A room or space having a volume less than 1.4 cu.m with 250 kCal of the aggregate input rating of all fuel burning appliances installed in that space.

An impairment of the quality of the potable water which creates an actual hazard to the public through poisoning or spread of disease by sewage, industrial waste also defined as high hazard.

A vertical vent that is a continuation of a drain to which the vent connects to the _____.

A drain connecting the compartments of a set of fixtures to a trap connecting other permitted fixtures to a common trap.

Marking on a backflow prevention device or a vacuum breaker is a point conforming to approved standards and establish by the testing laboratory.

Any connection or arrangement, physical or otherwise, between a potable water supply system and any plumbing fixture which enables nonpotable, used, unclean, polluted contaminated to enter into any part of a potable water system under any condition.

The liquid or water-borne waste derived from the ordinary living processes, free from industrial waste and of such character that permit satisfactory disposal without special treatment.

A pipe fitting with adjacent reverse bends and shape like the letter “S”.

Two offsets in successions or in series such that the centerline of the outside ends are in the same straight line.

A pipe which carries ground and surface water, storm water or waste water into the building drainage system.

The water supply pipe between the fixture supply pipe and the water distributing pipe.

The drain pipes from the trap of a fixture to the junction of that drain with any other drain pipe.

A water supply pipe connecting the fixture with the fixture branch.

The level in a fixture at which water begins to overflow over the top rim of the fixture.

Is the edge of a receptacle from where water overflows.

A fixture is flooded when the liquid therein risers to the flood level rim.

A tank located above or integral with water closet, urinal or similar fixture for flushing or removing excrement in the fixture.

It is a device located at the bottom of the tank for the purposed of flushing water closet and similar fixtures.

Is integrated within an air accumulator vessel which is design to discharge a predetermine a quantity of water into fixture for flushing purposes.

Is a device which discharges a predetermined quantity of water into fixtures for flushing purposes and is actuated by direct water pressure.

A return bend of small-sized pipe, one end of which is about 30 cm long and other end is about 7.5 cm long. Commonly used as a faucet for a pantry sink.

An interceptor of at least 3 cu.m. capacity to serve or more fixtures and which is remotely located.

The water that stands or passes through the ground.

A branch vent that performs its function for two (2) or more traps.

Is any pipe of fitting installed in a horizontal positioned or which forms at an angle not more than 45 deg. with the horizontal.

Any pipe or fitting installed in a vertical positioned or which forms at an angle of not more than 45 degrees with the vertical line.

Are cast iron soil pipes with plain ends connected together with bolted stainless steel band and neoprene gasket.

Is a pipe does not connect directly with the drainage system but conveys liquid waste by discharging into a plumbing fixture and directly connected to the drainage system.

Is a device designed and installed to separate and retain deleterious, hazardous or undesirable matters from normal sewage or liquid waste to discharge into the disposal terminal by gravity.

In plumbing, a secondary pipeline. In sewerage, a common sewer to which no other branch sewer is connected. It receives sewage from building sewer service connection only.

Is the discharge from any fixture, appliances or appurtenance in connection with a plumbing system which does not receive fecal matter.

A pipe or shaft to convey foul air from a plumbing fixture or a room to the outer air.

Any system of continuous piping, which is the principal artery of the system where branches are connected.

The purposed for which a building is used or intended to be used.

In a line of piping parallel is a combination of elbow or bends, which brings one section of the pipe out of line but into a line parallel with original section.

Whenever any work regulated by this Code is dangerous to human life or detrimental to health and property and inadequate or unsafe supply and or sewage disposal system.

Tube made of plastic material and colored black. The cross-sectional shape is normally oval and is denoted by its outside diameter.

Tube made of plastic material and colored black. The cross-sectional shape is circular is denoted by its outside diameter or O.D.

Any one of special class of device or equipment or intended to perform a special plumbing function, such as motors, heating elements and pressure-temperature elements.

A manufactured device or prefabricated assembly or an on the job assembly of component parts, and serves as adjust to the basic piping system and plumbing fixtures.

An approved type installed receptacles, devices or appliances supplied with water or receive liquid or liquid borne waste and discharge such waste into the drainage system.

The administrative authority or the officer with the administration and enforcement of the NPC or his regularly authorized authority.

An impairment of the quality of a water to a degree which creates hazard to the public health and adversely affect the aesthetic and potable qualities of water for domestic used.

Water satisfactory for drinking, culinary and domestic purposes and meets the requirement of the Philippine national standard for drinking water.

The normal force exerted by a homogeneous liquid or gas, per unit of area on the wall of the container.

The pressure existing without any flow motion.

The pressure available at the fixture or water outlet; allowance is made for pressure drop due to friction loss, head, meter and other losses in the system during maximum demand period.

Is the single sloping drain from the base of a stack to its junction with the main building drain.

A building sewer, which receive the discharge from more than one building and conveys it to a public sewer, private sewage disposal system or other point of disposal.

An outhouse or structure used for the deposition of excrement.

A pit beneath a privy where excrement connects.

A common sewer directly controlled by public authority to which all abutters have equal right of connection.

Potable water piping color coded pipe.

Drainpipes manufactured with toxic components and are color coded of?

An approved plumbing fixtures or device of such materials, shape and capacity to adequately receive the discharge from indirect waste pipe, constructed and located to be readily cleaned.

Include all valves controls used in plumbing system which are accessible.

Made up of two 90 deg. bends with inside and outside threads, flanged or welded fittings; and applied also to a or 180 deg. bends in copper tubings.

Waste water containing human excrement and liquid household waste. Also called “domestic sewage”.

A sewer intended to receive sanitary sewage with or without industrial waste and without the admixture of rain or ground water.

A loosely line excavation in the ground, which receives the discharge of a septic tank.

The pipe from the street water main or other source of water supply to the building served.

Any waste water containing animal or vegetable matter in suspension or solution and may include liquids containing chemicals in solution.