[PC] QB 02 | BEP 06

When connecting plastic pipe to other types of piping, the specific transition intended shall be made with approved?

A pipe joint obtaining by joining metal parts with metallic mixtures which melts at a temperature from 149°C – 427°C.

Any joint obtained by joining metal parts with alloys which melt at temperatur higher than 449°C but lower than the melting temperature of the parts to be joined.

The code of Sanitation of the Philippines with implementing Rules and Regulations.

An outhouse or structure used for the deposition of excrement.

A tee with branch to receive a threaded pipe or fittings.

In case of renewal of expired plumbing permit, a fee of equivalent to _____ of the original fee.

Sanitary Engineering Law.

Any two or more similar adjacent fixtures which discharge into a common horizontal soil or waste branch.

Each cleanout in piping 51 mm or less in size shall be installed so that there is clearance of not less than _____ in front of the cleanout.

No building sewer or other drainage piping or part thereof, constructed of materials other than approved for use or within the building shall be installed under or within _____ for any building or structure.

The water used test shall be obtained from a potable source of supply. A _____ air pressure may be substituted for the water test.

All shower compartments, regardless of shape shall have a minimum finished interior area of _____ and shall be capable of encompassing a 762 mm diameter circle.

Copper tubing in horizontal piping shall be supported at approximately _____ interval for piping 38 mm diameter and smaller.

Copper tubing in horizontal piping shall be supported at approximately _____ interval for piping 51 mm diameter and larger.

The commercial size of cast iron pipe hub type is _____.

The hubless is used in lieu of the pipe when caulking and jointing of the pipe is quite difficult. The hubless pipe (cast iron) is easily joined by use of _____.

A pipe between the water meter to the fixtures.

The rim over which water would spill on the floor.

An adequate _____ is one of the most important governances in modern and healthful human existence that involves air, water and food which is the basic necessities of life.

Minimum air gap for water distribution of sinks, laundry trays, gooseneck bath, faucets and other fixtures with effective openings not greater than 19 mm in diameter.

Supports of cast iron soil pipes shall be adequate to maintain alignment and to prevent sagging and shall be placed within _____ of the hub or joint.

Plastic pipe shall be supported at every _____ interval.

A stop valve place in service pipe near its connection with the water main is called?

What is CS and PS means?

Solder and fluxes with lead content with exceeds _____ are prohibited in the piping systems used to conveyed potable water.

What is water fixture supply unit of privately use bathtub?

Potable water inlet to gravity tank shall be controlled by a _____ float switch or electrode type of level water level control to prevent the tank from overflow.

When potable water is discharge to the drainage system, it shall be my means of approved air gap of 2 pipe size diameter from the supply of the outlet and top surface of the drainage inlet, but in no case shall be less than _____.

When shower receptors are built above ground, the sub floor and rough side of walls to a height of no less than _____ above the top of the finished dam or threshold shall be first lined.

Fittings on screwed pipe joints shall be of the _____ drainage type.

Another term for interceptor.

If the vent is near any doors, window, air shall or scuttle of a building. It should be extended over the highest opening by these much.

Drainage fittings shall be:

Urinal shall not be closer to _____ center to center distance.

The minimum size of cleanout allowed to serve a 4″ drain line is?

The distance between trap and vent should not more than?

The maximum trap loading for a 4″ diameter pipe shall be:

The maximum of water closets on a 3-inch stack is?

The maximum trap loading for a 2″ trap is?

The maximum trap loading for a 3″ trap is?

The trap and trap arm size of a wash basin in sets shall be:

The trap and trap arm size of an interceptor for grease, oil, etc. shall be:

The trap and trap arm size of an interceptor for sand, auto wash, etc. shall be:

For continuous flow into a drainage system, such as from sump pump or ejector, air conditioning equipment or similar devices, _____ shall be allowed for every 0.063 lps of flow.

Trap sizes shall not be increased to a point where the fixture discharge may be inadequate to maintain their self-scouring properties.

Cleanouts shall be provided for pressure drainage systems.

According to existing plumbing code; cast iron pipes, weld steel pipes, vitrified clay, concrete and asbestos pipe shall conform to?

The valve for controlling two or more outlets, is a cold water supply lines may be?

Fixtures outlets shall not be connected to the horizontal excreta drainage piping system within _____ of any vertical to horizontal change of direction of a stack containing suds-producing fixtures.

The maximum slope of 3″ horizontal pipe shall not be less than;

A tank shall be maintained an air pressure of not less than 3 kg for each meter of height the sewage is raised.

The minimum size of any pump discharge or any discharge pipe from a sump having a water closet connected thereto shall not be less than _____ diameter.

The trap of the floor drain shall be placed not more than _____ below the finished floor line, to facilitate cleaning in case of line trouble.

Recommended minimum size of the P-trap for floor drain is?

Installed at the bottom portion of the soil stack where the house drain is connected to receive the discharge from aerator?

Used as a terminal of the soil branch in each floor?

Always located near the stairs for use by firemen in case of fire?

It considers the building density in the locality and flammability of the structures and its content.

A vertical pipe usually used for the storage of water frequently under pressure.

Minimum of number of water closet required at Office 20 persons for employee use?

Minimum number of water closet required at elementary school for 35 females?

When a backflow prevention device does not bear a critical level marking, the part of the device that shall constitute the critical level is the _____.

Disposal of sewage, or other liquid waste shall be by means of _____.

Roofs, inner courts, vent shafts, light wells or similar areas having drains shall discharge to (a) _____.

The organization, office, or individual responsible for enforcing the requirements of a code or standard is the _____.

A mechanical device used to circulate hot water to the plumbing system?

Used on a smaller distribution system 6 m or less for elevating water wells or other sources.

It is inserted into the water main and it serves as the control of the water service.

Piping, fixtures or equipment that are installed so that they interfere with normal operation and use of windows or doors shall be _____.

The valve for controlling two or more outlets in a cold water supply line may be a?

Refers the pressure range measured over a period of 24 hours.

Air pressure in drainage pipes greater than atmospheric pressure.

Refers to an individual who worked in the sanitary field of ancient Rome.

It shall be the minimum cross-sectional area at the seat of the control valve or the supply pipe or tubing which feeds the device or outlet.

Airgap less than 25 mm shall only be approved as a permanent part of a listed assembly that has been tested under actual backflow conditions with vacuums of from?

Upright position, has a minimum of 150 mm or listed distance above all downstream piping and flood level rim of receptor as a function of device assembly.

As a function, it requires 30.5 cm minimum clearance at bottom for maintenance. May need platform/ladder for test and repair. May discharge water.

As a function, it requires 30.5 cm minimum clearance at bottom for maintenance. May need platform/ladder for test and repair. Does not discharge water.

A general requirement, where access and clearance shall require minimum of _____ space between the lowest portion of the assembly and the grade, floor or platform.

An approved atmospheric vacuum breaker is installed not less than _____ above the flood level rim of such trapped fixture, so that at no time will any such device be subjected to any backpressure.

Water closet and urinal tanks shall be equipped with a listed ball cock shall be installed with the critical level at least _____ above the full opening of the overflow pipe.

Water closet flushometer tanks shall be protected against backflow by an approved _____, device or method.

Water supply inlets not protected by atmospheric vacuum breakers shall be protected by approved _____.

Potable water outlet with hose attachments other than water heater drains and clothes washer connections shall be protected by a listed _____ or by a listed atmospheric vacuum breaker.

A device that shall not be located in any area containing fumes that are toxic, poisonous and corrosive.

Where a grounding system, acceptable to the AA is installed, inspected and approved metallic pipe may be replaced with?

Elevated or gravity tank vent shall be screened with a fine corrosion-resistant screen with openings not less than _____.

In water distribution system, it shall be installed on the water heating system in an approved location based on its listing requirements and the manufacturer’s instructions.

In water piping, it shall provide equivalent protection and application is restricted to those short pipe lengths at point of connection with fittings necessarily stripped from threading and jointing.

Unions shall be installed in the water supply piping within _____ away from regulating equipment, water heater, conditioning tank and similar equipment.

No water filter, water softener, backflow prevention device or similar devices regulated by this Code shall be installed in any potable water supply piping when the diameter of the inlet and/or outlet of may device or its connecting pipings are less than the diameter of the water supply distribution piping.

In water piping, it shall not compress, distort cut or abrade the piping and shall allow free movement of pipe.

It shall be tightly fastened with corrosive resistant fasteners up to to the floor with top surface 1/4 inch (6.4 mm) above finish floor.

It shall be installed at all changes in direction as tees and bends, change in size as reducers, stops as a dead ends and valves.

The result estimating continuous supply demands in LPS for lawn sprinklers, air conditioners, etc., and add the sum to the total demand for fixtures.

In WSFU, the weights for maximum separate demands may be taken as _____ of the listed demand for the supply.

In sizing water supply system, velocities shall not exceed _____ of the maximum values given in the appropriate installation standard.

Hot water piping system over _____ shall be provided with backflow preventer designed to operate without rendering any portion of the assembly inoperative.

PEX tubing shall be installed not less than _____ from the water heater.